Crude Rice Bran Oil Refining Machine ,Automatic Cooking Oil Machine
- >Type: automatic cooking oil machine
- Use: automatic cooking oil machine
- Condition: New
- Product type: automatic cooking oil machine
- Automatic Grade: Automatic
- Steam consumption: 450KG/T oil
- Circulating water cooling water yield: 150m3/H
- Electric consumption: 28Kwh/T oil
- Bleaching earth consumption: 5~50Kg/T oil
- Phosphoric acid: 2~3 kg/T oil
- Voltage: 380
- Production Capacity: 30-20TPD
1.Screening:Removing the chaff and broken rice in the rice bran, in case of they will influence the oil yield and the desolvent of wet meal in the next process. In the process of puffing section, the general requirement of impurity is less than 3%, and the requirement of crude fiber is about 8%.
2.Magnetic separation :Clearing the iron impurity which might be in the rice brain. Since in the process of puffing, the iron impurity will be harmful to the screw of extrusion machine, affect the puffing effect. As the rice brain particles are small and poor liquidity, the iron impurities are always be wiped off by the magnetic barrels installed in the feeding port.
3.Quenching and tempering :it is the process of preheating so that to improve the temperature of the rice bran before puffing. After quenching and tempering the temperature will be controlled at 65–75 °C, and the moisture will be controlled at 10 ~12%. Thus, on the one side, it can increase the output of the extrusion machine, and on the other side, it can improve the quality of the puffed rice bran.
4.Puffing: the rice bran is injecting high pressure steam and high temperature water through the extrusion machine, so that it can improve the temperature and moisture in the extrusion machine,and can also form the high pressure to process the rice bran. All these can make the the rice bran become porous columnar structure from the original pulverized state.All these effectively passivate the activity of various of enzyme in the rice bran, and destroy the fat layer structure, so that it will be easier for the oil yield.
5.Drying:The moisture of puffed material comes from the extrusion machine is too big and the temperature is too high for direct leaching, the must be experience to process of drying and coo-ling, thus the moisture will reach 7%–9%, and temperature will reach 50-55°C. After puffing, the rice brain are usually dried and cooled by plat dryer.
Crude rice bran oil refining machine,crude rice bran oil refining machine,automatic cooking oil machine
Introduction of crude rice bran oil refining machine,automatic cooking oil machine
1.Crude oil refining workshop is through take off impurity, Degumming, decoloring, deodorization, removeing wax, fractionation etc, to achieve different standards edible oil. At present, Having four grade of edible oil, different oil grade have different requirement for quality and machines. It is suitable for refining various crude vegetable oil, such as sunflower seed oil, tea seed oil, groundnut oil, cottonseed oil, palm oil, rice bran oil, soybean oil, corn oil and palm oil, etc. 2.Main parts:refining pot, decoloration pot ,deodorization pot, oil pumps and other parts
3.Advantage: 1.After refining the impurity of oil must be less than 0.2% ; 2.Recycling system save power and money ; 3.Lower oil waste.
working process of crude rice bran oil refining machine,automatic cooking oil machine
1.Pump crude edible oil into refining tank and heat with conduction oil, and the temperature will reach about 70°C-80°C after one hour.Add acid or alkali to separate according to the acid value. After one hour’s processing and 4-6hours deposit, then convey soap stock to storage tank.2.Pump refined oil into decoloring tank. When it is up to 90-110°C after one hour’s heating, add clay into tank for 20min’s processing. Then separate clay and oil with filter.
3.Put decolorizing oil into deodorization tank with vacuum pump. Heat and process with steam for odor removal. After filtering, you will get final oil product.
main parts functions of crude rice bran oil refining machine,automatic cooking oil machine
(1) Crude oil Refining section: used to P-acid de-gumming, alkali refining de-acid and water rinsing.
(2) Decoloring section: used to remove off pigments, bleaching oils and grease dehydrate.
(3) Deodorizing section: to remove off the odor components in oil.
(4) Dewax: used to remove off the wax in the oil, in order to get the high quality oil.
(5) Conduction stove: supply each device production needing heat energy, temperature reach above 280°C. (6) Steam generator: produce the needing steam for de-odoring and distillation.
(7) Vacuum pump: supply needing vacuum for dehydrate, de-color, de-odor. Vacuum degree can reach above 755mm Hg.
(8) Press filter: filter clay, filter out clear oil.
(9) Air compressor: blow dry bleached clay, blow empty the leftover oil in the press filter.
WorkGroup has applied the automatic control system with advancedness, security, reliability into the pretreatment, extraction, refining and fractionation in large oil plants. For its application in automatic control system, it can control the production in the entire workshop and monitor the operational status of each device by controlling the computer terminals in the room. One person only can operate the entire workshop, with efficient production management. It has reduced the production cost greatly and improved the management efficiency.
System evaluation: 1. Project basic situaction
Solution: 1. The investment budget 2. Site measurement 3. Technical discussion
Product selection: 1.Factory inspection 2. Site measurement 3. Technical discussion 4. Supply professional drawing and lists
Win-win cooperation: 1. Sign the contract 2. Wstablish mutual benefit, strategic cooperative partnership.
Design evaluation: 1. Detailed technical assessment, arrangement 2. Design of process and equipment layout
Procurement: Strictly inspection, optimized selection.
Installation: 1. Quality and quantity guaranteed 2. Completion of hand over
Acceptance: 1. Acceptance test 2. Accepted deliverables
Technical traning: 1.On-site installation and products training 2. Operation skills training 3.Maintenance training 4. Centralized technical training
Technical service: Long time technical service
Accessories supplying: Supplying spare parts with cost
Complaint handling: 12-24 hours response mechanism
Client Review: 1. Call-back 2. Regular return visit.
Packaging & Shipping
If you are interested in our products, please kindly send me your inquiry details in the Below, Click “Send” Now!
WorkGroup believe that whatever the field is, quality has always been at the heart of the company’s performance. We treat quality and service as a way of life and hope to serve you in the possible manner on a long term and mutually beneficial basis. If you want to know more information about our sunflower oil plant or any other seed processing plant, please contact us in the following form. Our responsible, experienced sunflower oil processing technical team is always ready to serve and guide you at any time.
All the other oil seeds pre-treatment and oil refining equipment, sheller, cleaning sieve, cooker, filter and others is available at WorkGroup. If you want to know to start a vegetable oil pressing line with oil press machine, please contact us, we will offer you the best plan.
Oil Processing Machinery Related Products
Client feedback means a lot to us, and we ensure that a partnership with WorkGroup provides our clients the insights needed to make informed decisions. Read our testimonials and find out what our customers say about our work.
"Three years ago, We decided to set up a soybean oil mill plant to process soybean. We finally choose Workgroup as our supplier. The whole process of setting up was unexpectedly smooth. And the produced soybean oil is the first class and sold very well in our market."
"Machine designed to perfection, operation and aesthetic are wow, using it is fun and easy to crush oil. Thanks to workgroup team and management for providing excellent palm oil press machine in africa market. Congratulations. I want to point out some design or operation flaws nut there is none to nill."
"I would like to personally thank you and your team for the sunflower oil factory equipment. The team had an in-depth understanding of factory processes and completed our requirements on time and with high quality"